Shower channel
Pera. Open, elegant, floor-level.
Visible drainage on an open channel body with built-in fall. Up to 160 cm, can be cut down from 32 cm, 360° rotating drain pot.
60 mmBuild height from 60 mm, ideal for renovation
80–160 cmfive lengths, can be cut to any size from 32 cm
360°rotating drain pot, DN 50 outlet
Build-up
The drain you are allowed to see.
Pera shows the water: the open channel body with its built-in fall carries it visibly to the outlet. No grate, no frame, nothing that can clog. Cleaning takes seconds.
Frame and cover in stainless steel 1.4301, waterproofing membrane fitted watertight at the factory, abP-tested.
From shell to tile.
Keep scrolling: three steps, one picture.
Fit and connect.Channel body with siphon in the screed, 15 cm from the wall in this example, DN 50 side outlet.
Fall towards the channel.The floor is laid with a two per cent fall towards the channel.
A cut in the stone.What remains is a line of stainless steel in the floor.
Technical data.
| Material | Stainless steel 1.4301 / V2A (AISI 304), frame and cover |
|---|---|
| Lengths | 80 · 100 · 120 · 140 · 160 cm, can be cut from 32 cm |
| Build height | from 60 mm |
| Drain | 360° rotating drain pot, DN 50 outlet, integrated trap |
| Flow rate | 0.80 l/s (48 l/min) with the standard siphon, trap water height 25 mm |
| Waterproofing | Waterproofing membrane fitted at the factory, abP-tested bonded waterproofing system |
| Application | Floor-level showers in housing, hotels, spas and sports facilities; new build and renovation |
| Testing | abP, EN 1253 |
Ordering information.
12 variants.
| Item number | Size | Surface |
|---|---|---|
| LP13-H24L100E9 | 100 cm | Brushed anthracite |
| LP13-H24L100E1 | 100 cm | Brushed stainless steel |
| LP13-H24L120E9 | 120 cm | Brushed anthracite |
| LP13-H24L120E7 | 120 cm | Brushed bronze (PVD) |
| LP13-H24L120E4 | 120 cm | Brushed gold (PVD) |
| LP13-H24L120E1 | 120 cm | Brushed stainless steel |
| LP13-H24L140E1 | 140 cm | Brushed stainless steel |
| LP13-H24L160E9 | 160 cm | Brushed anthracite |
| LP13-H24L160E1 | 160 cm | Brushed stainless steel |
| LP13-H24L80E9 | 80 cm | Brushed anthracite |
| LP13-H24L80E1 | 80 cm | Brushed stainless steel |
| Project-specific versionsNot held in stock. Manufactured for your project; lead time on request. | ||
| LP13-H24L60E1 | 60 cm | Brushed stainless steel |
Identical for every variant: Material Stainless steel 1.4301 / V2A (AISI 304) · Outlet DN 50
Special lengths on request. Every channel can be cut to size on site.
Installation in five steps.
The order follows the site: shell first, tile last.
ShellPosition the channel, connect it to the drainage and set the height.
Screed workLay the screed with a fall towards the channel; the protective cover sets the height.
WaterproofingRemove the protective cover and bond the waterproofing membrane into the bonded waterproofing.
Tiling workTile the floor with a fall towards the channel and grout the joints.
CoverInsert the cover and peel off the protective film last.